Tuesday, June 9, 2009
How to program Mitsubishi Remote
Mitsubishi keyless remote programming instructions:Programming:(Note: Entering new remote transmitter codes will erase all old codes. All remote transmitters must be programmed together.)-Ensure ignition switched OFF.-Access data link connector (DLC) located behind fascia.-Jump DLC terminal 1 and ground. ( should be done with diagnostic equipment).(Note: Terminal 1 may also be grounded using diagnostic equipment connected to the DLC.)-Within 10 seconds: Press hazard switch six times.-Doors should lock and unlock to confirm registration mode.-Press and release remote transmitter LOCK button.-Within 10 seconds: Press remote transmitter LOCK button twice.-Doors should lock and unlock to confirm registration.-If registering additional remote transmitters, within 1 minute: Repeat button procedure for each remote transmitter.-Doors should lock and unlock to confirm registration.Note: To exit programming mode: Remove key from ignition or remove jump lead.Note: A maximum of 4 remote transmitters can be programmed.
Friday, June 5, 2009
How To Program Subaru Outback Remote 2005
Programming new remotes The keyless entry system is equipped with a code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different.
To register a new transmitter with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote. If there is no bag, open the remote and make a note of the eight-digit number.
the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone nor the buzzer will sound and the interior lamp will not flash. In this event, start all over again.
To register a new transmitter with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote. If there is no bag, open the remote and make a note of the eight-digit number.
the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone nor the buzzer will sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the eighth digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you wish to program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the eighth digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you wish to program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
How To Program Volkswagon Passat Remote
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: The "Open" button is pressed once for programming the first, or a single, remote unit. When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
Mechanically lock vehicle at left front door, using second key.
On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. Switch ignition off. As many as 4 new remote units can now be coded
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: The "Open" button is pressed once for programming the first, or a single, remote unit. When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
Mechanically lock vehicle at left front door, using second key.
On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. Switch ignition off. As many as 4 new remote units can now be coded
How To Program Toyota Camry Remote
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
How To Program Lexus ES 300 Remote
1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
How To Program Lexus ES 300 Remote
1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
How To Program Acura TL Remote 1997
Note: Entering the programming mode cancels all learned keyless remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode.
You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. You must program remotes within 10 seconds of each other
1. Turn ignition switch to ON (II)
2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.)
3. Within 4 seconds turn ignition switch to LOCK (0) position
4. Within 4 seconds turn the ignition switch to ON (II)
5. Repeat steps 2, 3 and 4 two more times using the same keyless remote used in step 2
6. Within 4 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm you are in programming mode.
7. Within 10 seconds press the LOCK or UNLOCK button on same remote. 8. Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.
9. Turn the igniton switch to LOCK (0) to exit programming mode.
10. Test remote(s)
You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. You must program remotes within 10 seconds of each other
1. Turn ignition switch to ON (II)
2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.)
3. Within 4 seconds turn ignition switch to LOCK (0) position
4. Within 4 seconds turn the ignition switch to ON (II)
5. Repeat steps 2, 3 and 4 two more times using the same keyless remote used in step 2
6. Within 4 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm you are in programming mode.
7. Within 10 seconds press the LOCK or UNLOCK button on same remote. 8. Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.
9. Turn the igniton switch to LOCK (0) to exit programming mode.
10. Test remote(s)
Subscribe to:
Posts (Atom)