Tuesday, June 9, 2009

How to program Mitsubishi Remote

Mitsubishi keyless remote programming instructions:Programming:(Note: Entering new remote transmitter codes will erase all old codes. All remote transmitters must be programmed together.)-Ensure ignition switched OFF.-Access data link connector (DLC) located behind fascia.-Jump DLC terminal 1 and ground. ( should be done with diagnostic equipment).(Note: Terminal 1 may also be grounded using diagnostic equipment connected to the DLC.)-Within 10 seconds: Press hazard switch six times.-Doors should lock and unlock to confirm registration mode.-Press and release remote transmitter LOCK button.-Within 10 seconds: Press remote transmitter LOCK button twice.-Doors should lock and unlock to confirm registration.-If registering additional remote transmitters, within 1 minute: Repeat button procedure for each remote transmitter.-Doors should lock and unlock to confirm registration.Note: To exit programming mode: Remove key from ignition or remove jump lead.Note: A maximum of 4 remote transmitters can be programmed.

Friday, June 5, 2009

How To Program Subaru Outback Remote 2005

Programming new remotes The keyless entry system is equipped with a code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different.
To register a new transmitter with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote. If there is no bag, open the remote and make a note of the eight-digit number.
the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence

1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc

2. Open and close the driver's door one time.
then Within 45 seconds

3. open and close the driver's door once

4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone nor the buzzer will sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the eighth digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you wish to program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right

How To Program Volkswagon Passat Remote

1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.

2. Mechanically lock vehicle at left front door, using second key.

3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.

4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
􀀹 Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
􀀹 Mechanically lock vehicle at left front door, using second key.
􀀹 On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. 􀀹 Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. 􀀹 Switch ignition off. As many as 4 new remote units can now be coded

How To Program Toyota Camry Remote

1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.

2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

How To Program Lexus ES 300 Remote

1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.

3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.

4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes

How To Program Lexus ES 300 Remote

1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.

3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.

4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes

How To Program Acura TL Remote 1997

Note: Entering the programming mode cancels all learned keyless remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode.
You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. You must program remotes within 10 seconds of each other

1. Turn ignition switch to ON (II)

2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.)

3. Within 4 seconds turn ignition switch to LOCK (0) position

4. Within 4 seconds turn the ignition switch to ON (II)

5. Repeat steps 2, 3 and 4 two more times using the same keyless remote used in step 2

6. Within 4 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm you are in programming mode.

7. Within 10 seconds press the LOCK or UNLOCK button on same remote. 8. Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.

9. Turn the igniton switch to LOCK (0) to exit programming mode.

10. Test remote(s)

How To Program Acura RL Remote

AT TIME OF PROGRAMMING, ALL REMOTES (UP TO 3) TO BE PROGRAMED/REPROGRAMMED MUST BE PRESENT.

The following steps 1-12 are done on a single remote, step 13 is done on all remotes to beprogrammed. (Up to 3 can be programmed)

1) Get into the car shut the doors and make sure they are unlocked

2) Turn on the ignition (do not turn on the car just the ignition

3) Press the lock button on remote

4) Turn key to the accessory ON position (your radio works in this mode

5) Turn on the ignition (do not turn on the car just the ignition

6) Press the lock button on remote

7) Turn key to the accessory ON position (your radio works in this mode

8) Turn on the ignition (do not turn on the car just the ignition

9) Press the lock button on remote

10) Turn key to the accessory ON position (your radio works in this mode

11) Turn on the ignition (do not turn on the car just the ignition)

12) Press the lock button on the remote, the locks should chirp to indicate that programming mode was entered successfully

13) Press the LOCK button on remote, the doors should chirp again to confirm programming. PRESS THE LOCK BUTTION ON EACH OF THE REMAINING REMOTES TO BE PROGRAMMED (ONE AT A TIME)


14) Turn off the car fully and try locking/unlocking with remote

Below step is optional:

To turn on/off the chirping when locking/unlocking with remote do the following:

1) Press the trunk release button on the remote and hold it


2) While holding, press the LOCK button on remote and hold it, the led on the remote will flicker for about 1sec


3) After the LED goes off, release both buttons and test it

4) The procedure for chirp on and chirp off is the same, this needs to be done on all remotes otherwise only the one programmed will allow chirping while the others will still be silent or vise versa.

How To Program Honda Remote

Difficulty: Easy
Instructions
Things You'll Need:
A Honda vehicle with keyless entry
a key to the vehicle
ALL keyless remotes to be programmed for the vehicle (you have to program them all together) a non-programmed remote will work for this process

Step 1
Unlock the doors.

Step 2
Turn key to position II.
Turn the ignition key to the "ON" (II) position. (This is the position where the key sits while you're driving. The accessories should come on and the dashboard will light-up.)

Step 3
Your remote may look slightly different.
Press the "LOCK" or "UNLOCK" button on the remote control transmitter.

Step 4
Turn key to position 0 or I. (Shown in position 0)
Turn the ignition key to the "OFF" (0 or I) position.

Step 5
Turn key to position II.
Turn the ignition key to the "ON" (II) position.

Step 6
Your remote may look slightly different.
Press the "LOCK" or "UNLOCK" button on the remote control transmitter.

Step 7
Turn key to position 0 or I. (Shown in position 0)
Turn the ignition key to the "OFF" (0 or I) position.

Step 8
Turn key to position II.
Turn the ignition key to the "ON" (II) position.

Step 9
Your remote may look slightly different.
Press the "LOCK" or "UNLOCK" button on the remote control transmitter.

Step 10
Turn key to position 0 or I. (Shown in position 0)
Turn the ignition key to the "OFF" (0 or I) position.

Step 11
Turn key to position II.
Turn the ignition key to the "ON" (II) position.

Step 12
Your remote may look slightly different.
Press the "LOCK" or "UNLOCK" button on the remote control transmitter.• The power door locks cycle to indicate programming mode.• To terminate the programming mode at this point, either turn the ignition key to the "OFF" position or leave the remote’s button untouched for over 10 seconds.• To program, continue to step 13.

Step 13
Press the "LOCK" button of each remote (one at a time) to be stored in memory. Remember to program ALL remotes during this step.
Press the "LOCK" button of each remote (one at a time) to be stored in memory.• The power door locks cycle to confirm each entry.• A button on EACH remote control transmitter to be programmed MUST bepressed. Perform this programming step within 10 seconds for each remote or else the programming mode will terminate and some remotes may not be programmed.Note: Only 3 remotes can be stored in the system’s memory.

Step 14
Turn key to position 0 and

How Program GM Remote

Step 1
First you will need to buy the remotes required for the keyless entry. You can purchase these off of eBay for a fair price, much cheaper than the dealer. Note that this process only works for GM and Chevy Vehicles.

Step 2
First get in the vehicle and make sure all the doors are shut.

Step 3
Insert the key into the ignition.

Step 4
Press and hold the drivers side unlock switch. While holding the switch turn the key to ON, then OFF, then ON, then OFF again. Let go of the unlock switch and the doors should then lock and unlock. The car is now in program mode.

Step 5
Press and hold the unlock and lock button the keyless entry remote. Hold the buttons for about 20 seconds. The doors will then unlock and lock again. This means that this remote has been programmed. Repeat the steps for any other keyless entry FOB remotes to program.

How To Program A Nissan Remote

Step 1
The first step is to actually get the remotes. If you already have the remotes, proceed to step 2. If you do not, get on eBay and find the remotes for your year and model Nissan. You can usually get them for about $50 a pair, shipped. This is at least half of what the dealer will charge you.

Step 2
Open the drivers side door of the vehcle and get in the vehicle. Close the door. Press the lock button on the drivers side door to lock all the doors.

Step 3
Insert your key into the ignition and remove it at least 6 times. It may take up to 10 times. This needs to be done in a good pace, but not too fast. At least 6 times within 10 seconds is about right. If you have done it right, you will see the hazard lights flash twice.

Step 4
Once you see the hazard lights flash twice, the car is now in program mode. Insert the key back into the ignition and turn it to ACC. Push any button on your keyless entry FOB remote ONCE. This should be done within 5 seconds of turning the key to ACC. You should notice your hazards flash again. If you have another remote to program proceed to step 5, otherwise turn the key off and remove it. The remote should now be programmed.

Step 5
If you have another keyless entry remote to program unlock the door with the drivers side power lock and then lock them again. Press any button on the next remote. Turn the key back to the original position and remove the key. The remotes should now be programmed.